SPLnFFT Noise Meter7.1 - App Store
Sie können Ergebnisse sehen in einige Sekunden.
Herausgeberbeschreibung
SPLnFFT ist ein Lautstärkemessgerät mit zusätzlichen Funktionen wie einem FFT-Viewer oder Testsignal-Generator. Das ist ein Allroundprodukt zu einem sehr erschwinglichen Preis.
Sie benötigen unbedingt ein Mikrofon mit dieser App, entweder das integrierte (iPhone/iPad) oder das externe (iPod 2. Generation).
Top Digitalanzeige für die Messung der Schallleistungspegel im Langsam-Modus (gemittelt über 1s). Zentrale analoge Anzeige für Schnell-Modus (gemittelt über 1:8 s). Peak-Wert wird angezeigt, bis Sie den Touchscreen zu berühren.
Ein richtiges Lautstärkemessgerät schlägt einige Gewichtungen. Sie können Gewichtungen A, B oder C wählen (Suche nach "A-Bewertung" auf "Wikipedia" für weitere Informationen).
Die Ansicht unten ist ein Echtzeit-FFT. Sie werden bemerken, dass die vorherrschende und die nächstschwächere Frequenz hervorgehoben sind. Diese Frequenzen und ihre relative Stärke sind auf der rechten Seite angezeigt.
Die grüne Linie ist das Ergebnis einer Echtzeit FFT mit 1024 Punkten. Die lila Linie ist die gemittelte FFT ("alpha ,1-alpha" auf Stärke jede Frequenz getan). Die blaue Line ist eine Kopie von dem, was die lila Linie war, als der Benutzer die Anzeige der letzten Zeit anhielt.
Ein Testton bei 1kHz oder ein weißes Rauschen oder Rosa Rauschen wird erzeugt und versendet zum rechten und / oder linken Ausgäng (wählen Sie die gewünschte Seite über BEEP). Diese FFT Kurve - genauer eine Vergrösserung davon - kann als ein Bild in Ihrer eigenen Foto Bibliothek exportiert werden, indem die Kamera-Taste gedrückt wird (Kamera-taste nur aktiv, wenn Anzeige angehalten).
Das Display kann gedreht werden upside-down um die Lektüre zu erleichtern: Drehen Sie einfach Ihr iPhone mit gedrückter vertikal.
Wie für alle Lautstärkemessgeräte (unabhängig von ihrem Preis), ist eine Kalibrierung notwendig, wenn Sie extreme Präzision erreichen wollen. Dies ist auf dieser App mit einem Drehknopf möglich, damit Sie die Lautstärge kalibrieren und das Ergebnis in einem der drei nicht flüchtigen Speicher speichern. Wie? Für die Kalibrierung benötigen Sie eine externe Referenz und entweder ein kalibriertes Messgerät oder einer kalibrierten Rauschquelle.
Beachten Sie auch, dass die winzigen Einbau-Lautsprecher keine extremen Frequenzen wiedergeben kann. Also, wenn Sie echtes weißes oder rosa Rauschen hören wollen, benötigen Sie einen Kopfhörer oder eine gute HiFi Anlage.
Diese App wurde hauptsächlich für meine eigenen Bedürfnisse zugeschnitten. Ich bin ein Experte Signalverarbeitung und Sie können andere Audio-Anwendungen von mir im AppStore finden.
Ein Kommentar, Feedback? Es gibt ein Blog.
Über SPLnFFT Noise Meter
Das Unternehmen, das SPLnFFT Noise Meter entwickelt, ist Fabien Lefebvre. Die neueste vom Entwickler veröffentlichte Version ist 7.1.
Um SPLnFFT Noise Meter auf Ihrem iOS-Gerät zu installieren, klicken Sie einfach auf die grüne Schaltfläche Weiter zur App oben, um den Installationsvorgang zu starten. Die App ist seit 2023-12-24 auf unserer Website gelistet und wurde 0 Mal heruntergeladen. Wir haben bereits geprüft, ob der Download-Link sicher ist; zu Ihrem eigenen Schutz empfehlen wir jedoch, die heruntergeladene App mit Ihrem Antivirusprogramm zu scannen. Ihr Antivirusprogramm kann SPLnFFT Noise Meter als Malware erkennen, wenn der Download-Link defekt ist.
So installieren Sie SPLnFFT Noise Meter auf Ihrem iOS-Gerät:
- Klicken Sie auf unserer Website auf die Schaltfläche Weiter zur App. Dadurch werden Sie zum App Store weitergeleitet.
- Sobald SPLnFFT Noise Meter im iTunes-Eintrag Ihres iOS-Geräts angezeigt wird, können Sie den Download und die Installation starten. Tippen Sie rechts neben der App auf die Schaltfläche LADEN, um den Download zu starten.
- Wenn Sie nicht in der iOS App Store App angemeldet sind, werden Sie nach Ihrer Apple-ID und/oder Ihrem Passwort gefragt.
- Nachdem SPLnFFT Noise Meter heruntergeladen wurde, sehen Sie rechts einen INSTALLIEREN-Button. Tippen Sie darauf, um die eigentliche Installation der iOS-App zu starten.
- Sobald die Installation abgeschlossen ist, können Sie auf die Schaltfläche ÖFFNEN tippen, um sie zu starten. Das Symbol wird außerdem zum Startbildschirm Ihres Geräts hinzugefügt.
Programmdetails
Systemanforderungen
Download-Informationen
Preisgestaltung
Versionsgeschichte
Version 7.1
veröffentlicht am 2023-12-24
No more long press to change frequency weightings.
Re-compiled for latest iOS. Better handling of various screen sizes and shapes.
Version 7.1
veröffentlicht am 2026-10-15
Version History No more long press to change frequency weightings.
Re-compiled for latest iOS. Better handling of various screen sizes and shapes. 7.1 12/24/2023 Optimized for latest iPhones and iOS.
Note that iPhone X and later do NOT support any more upside down orientation. 7.0 02/20/2020 Minor update for the HTTP GET feature: unique identifier added 6.91 10/15/2018 Broken links to external webpages repaired.
New set of durations for 'HTTP GET' feature. 6.9 07/19/2018 Native support of new kind of display as offered by iPhoneX for example.
New feature added in the advanced features pack: the ability to export main data regularly to a distant web server through a HTTP GET request. 6.8 05/31/2018 Version 6.6 was problematic with iOS 8. Thus skipping this version v6.6.
iOS 8 users can retrieve version 6.5 instead (delete current installation if you already installed v6.6), whereas iOS9/10 users can keep using v6.6 or update to v6.7.
For information, this is just to support the latest and only supported version of Dropbox API. This means as well that Dropbox feature is now no more compatible with iOS8. 6.7 06/20/2017 New SDK being used for Dropbox since previous one will soon be dropped. This should be transparent to end users. Except that initial association has to be re-run in 'Conf' tab: 'link to Dropbox'.
New external link to replace broken ones.
!!! DO NOT UPDATE IF USING iOS 8 !!! (no issue with iOS 9 or 10) 6.6 06/12/2017 Previous update was quite major:
Screenshots now contain metadata including keywords and GPS data, provided you authorised the App to access such data.
Added more choices for external microphones in general settings of the iPhone. Force close then re-open the App after changing these new settings.
New advanced features included in the optional pack:
_ load calibration files for frequency analysis from Dropbox directory, the same one being used for uploading .bin files. See 'i' page for detailed instructions
_ 'Snap' tab added: take a photo of the surroundings with current sound level displayed on top of it. Will be stored to local photo library (of course this requires you to allow access to camera when requested to do so. Otherwise go to iPhone settings/SPLnFFT)
This update brings fine tuning of the new optional feature 'Snap':
_ no more warning message if disable verbose mode is activated. The camera icon will disappear shortly to validate the action
_ the 2 landscape orientations are now supported
And fixes one bug: metadata for date and time within recorded pictures were not set correctly for some of them 6.5 04/08/2017 Screenshots now contain metadata including keywords and GPS data, provided you authorised the App to access such data.
Added more choices for external microphones in general settings of the iPhone. Force close then re-open the App after changing these new settings.
New advanced features included in the optional pack:
_ load calibration files for frequency analysis from Dropbox directory, the same one being used for uploading .bin files. See 'i' page for detailed instructions
_ 'Snap' tab added: take a photo of the surroundings with current sound level displayed on top of it. Will be stored to local photo library (of course this requires you to allow access to camera when requested to do so. Otherwise go to iPhone settings/SPLnFFT) 6.4 03/29/2017 Some minor improvements and few smart updates, based on your feedbacks:
_ fine tuning of the 'SET' procedure in 'Mic' tab, when applicable. It is now recommended to avoid using LOW gain for frequency analysis, due to a slight filtering effect
_ dBr in analog views changed: so far reference was current Leq value. Now you can choose instead Leq sampled at last RESET, or 83dB (K-system)
_ you can pre-enter an address for export by mail
_ files exported by mail have a name appended with today's date 6.3 03/02/2017 Fixed a bug that prevented to save screenshots to photo library with latest iOS.
BAR view slightly modified to get closer to standard ANSI bands.
This tab was renamed to PSD to reflect more precisely what it does: average power spectrum density over each band. A new setting is proposed to display power per band instead. A pink test signal will show as flat with this new setting. 6.2 11/21/2016 IMPORTANT CHANGE !!!: Selecting dB(A), dB(C),... is less sensitive: a LONG PRESS of 1/3s is required now to avoid accidental changes.
Updated with a more recent Dropbox API.
Export to Dropbox is now restricted to the last 2 days. Before this, an old recording could have been exported with null data inside.
Pop-up "please review this App" was too intrusive with latest iOS. This is corrected and anyway instructions are given to disable it once for ever.
Landscape view is now available when the device is laying flat.
A new special mode for FFT averaging is now available: when selecting maximum value (Conf tab), averaging is done over the full period since last reset. The slider itself turns red in that case to identify that this new mode is indeed selected. 6.1 09/20/2016 This update is important to consider if using an external microphone (iMM-6, i436, ...):
_ pre-calibration was slightly adjusted for external microphones (if ever you used a sound calibrator then you should check again or contact us)
_ bug correction: in very particular conditions the 'SET' procedure (relative calibration between HIGH/MID/LOW gains) applied to an external microphone may have failed. No such issue detected with internal microphone. Users with external microphones may re-run this procedure
Pre-calibration for internal microphones was not modified. Most types of devices were tested again, including: iPhone 4S, 5S, 6, 6S and iPad 2, Air, Air 2.
You may have noticed that some iPads behaved differently with latest iOS. Just re-run the 'SET' procedure as you will be invited to by this update to complete this transition to latest iOS. iPhones still behave as previously.
This update is important as well for in-app purchase: on top of current feature it brings (export to Dropbox), new frequency weightings are introduced, for SIL="Speech Interference Level", along with a new time weighting (3s), all this simultaneously in one page. Feedback by mail/FB is welcome since this is quite new. Very old devices (iOS7) are dropped due to increased computing power which is required.
Introducing a new setting, that allows mixing audio from this this App with audio from other Apps. For example to play some audio from Music App and monitor your speakers with this App.
Since only few users will need this feature, it is quite hidden: go to iPhone settings, find the App, activate this option. Now kill this App (double click on home button, swipe this App off the top edge of the screen) and re-launch it. Launch the other App and start playing audio. Back to this one to monitor audio inputs. The other App should keep playing audio.
Note that SPLnFFT must be launched first, then switch to Music then back to SPLnFFT. 6.0 02/25/2016 Still improving the new "SET procedure" in Mic. tab: now gain calibration results for internal microphone become default values for external microphones.
This will be more convenient for those using external microphones.
Still this new feature: you can make a screenshot with the camera icon bottom right in running mode (when not in pause: in that case this is the export menu that pops in). 5.9 09/22/2015 Latest version was a major update: new gain setting, new SET procedure.
This one is minor:
_ behavior in AUTO mode slightly improved
_ the camera icon which was useless in running mode can now be used for a screenshot to be captured in your own photo library 5.8 09/16/2015 Internal gain setting heavily re-worked. A new range is defined - "MED" - which corresponds exactly to previous range "LOW". The new range "LOW" makes it possible to go even higher than before.
IMPORTANT: the "Mic. gain SET" procedure in Mic. tab should be re-run. It's a litlle longer to run but only one iteration is required now. Find a quiet room, set volume to maximum and launch the procedure.
SPLnFFT and SPLnWATCH should be both updated since they share settings including those concerning gains. 5.7 09/09/2015 Very minor bug corrected with the SET procedure: if launched while paused then the process failed. 5.6 07/24/2015 Rendering was improved for iPhone6/6+.
The info page was redesigned, and its existence is more obvious for new users. New links were added in particular for prevention of hearing loss. We will add other specific topics in this area on request: something is not clear in the usage of the App ? Contact us !
Remember that if you are annoyed by info messages (pop ups), there is an option in the Conf. tab to disable the verbose mode. 5.5 07/22/2015 Export to Dropbox: the date used in file names for time zones with negative offset (America...) needed to be corrected. Before correction there was a shift of one day in this area.
Microphone gain "AUTO": thresholds changed from 85/60 to 80/40.
Displayed device name: using now commercial name iso internal iOS name (just a cosmetic change). 5.4 05/01/2015 Updated to support natively latest architectures (arm64). No change expected from user's point of view.
Annoyed with warnings ? There is a new switch in Conf tab now.
Introducing latest optional feature - export raw data to Dropbox - as in-app purchase. Yet casual users still have opportunities to use it for free, provided they plan for it.
Note for export to Dropbox: the date used in the name of exported files is not correctly computed in time zones with negative offset (America,...). Add 1 day to what is indicated. This will be corrected in next update 5.3 03/18/2015 A new optional feature was introduced in version 5.0: export to Dropbox.
It is still under development:
_ new icon
_ new trial conditions, heavily relaxed
Coming soon:
_ this new optional feature available for purchase. Yet still available for trial for long periods
_ the ability to disable some warnings: less pop-up messages 5.2 02/06/2015 Major update for recent iPads: new offset applied. Before this modification measurements with internal microphone were over-estimated of 10dB on this type of device. No change for iPhones.
Any issue regarding installation or any other topic ? Contact me by mail: I cannot answer to comments in iTunes. 5.1 01/23/2015 Some smart updates, in particular for the "i" page
Introducing new optional feature, for advanced users: the ability to export a full day's measurements (Lp SLOW and FAST) to Dropbox, for further processing using your preferred tool: Matlab, GNU Octave, Excel, ... This feature once optimized will be proposed as in-app purchase
Next step:
_ release this new optional feature
_ adjust offset for latest iPad 5.0 01/08/2015 Completing migration to iOS8
Now the BAR view can be exported
Added a warning for pre-calibration of gains (LOW vs HIGH)
Storage space required for backup to iCloud minimized 4.9 10/15/2014 Ready for iOS 8.
Still one minor update required for iOS 8 adopters, to enable again adding current location when exporting data by mail: please be patient few more days. 4.8 09/27/2014
Version 7.1
veröffentlicht am 2023-12-24
Dec 24, 2023
Version 7.1
No more long press to change frequency weightings.
Re-compiled for latest iOS. Better handling of various screen sizes and shapes.
Version 7.0
veröffentlicht am 2020-02-20
Feb 20, 2020 Version 7.0
Optimized for latest iPhones and iOS.
Note that iPhone X and later do NOT support any more upside down orientation.
Version 7.0
veröffentlicht am 2020-02-20
20 feb. 2020 Version 7.0
Optimized for latest iPhones and iOS.
Note that iPhone X and later do NOT support any more upside down orientation.
Version 6.1
veröffentlicht am 2010-02-18
Version 7.0
veröffentlicht am 1970-01-01
2020년 2월 20일 Version 7.0
Optimized for latest iPhones and iOS.
Note that iPhone X and later do NOT support any more upside down orientation.
Version 7.0
veröffentlicht am 1970-01-01
20 февр. 2020 г. Version 7.0
Optimized for latest iPhones and iOS.
Note that iPhone X and later do NOT support any more upside down orientation.
Haftungsausschluss
Offizieller App Store-Link
Wir hosten SPLnFFT Noise Meter nicht auf unseren Servern. Wir haben es nicht auf Viren, Adware, Spyware oder andere Arten von Malware gescannt. Diese App wird von Apple gehostet und hat deren Allgemeine Geschäftsbedingungen erfüllt, um dort gelistet zu werden. Wir empfehlen Vorsicht bei der Installation.
Der App-Store-Link für SPLnFFT Noise Meter wird Ihnen von apps112.com ohne jegliche Zusicherungen, Gewährleistungen oder Garantien zur Verfügung gestellt, greifen Sie daher auf eigene Gefahr darauf zu.
Bei Fragen zu dieser speziellen App wenden Sie sich bitte direkt an den Herausgeber. Bei Fragen zu den Funktionalitäten von apps112.com kontaktieren Sie uns.



